part number size type part number size type N010-0510-T303 17.0 pen/finger n010-0551-t744 12.1 pen/finger n010-0510-t304 17.0 pen/finger n010-0550-t603 10.4 pen only n010-0510-t236 15.0 pen/finger n010-0550-t613 10.4 pen/finger n010-0510-t219 15.0 pen/finger n010-0550-t625 10.4 pen/finger (light touch type) n010-0550-t717 12.1 pen/finger n010-0550-t627 10.4 pen/finger (light touch type) 100mm tail n010-0551-t742 12.1 pen/finger n010-0550-t345 8.4 pen/finger standard resistive touch panel specifcation fid-550 7-wire series rohs compliant n part numbers touch panels: n features ? superior long life, using a unique construction method offering improved life over typical technologies; by sensing data input only on the glass layer, typically a 10x improvement in product life is achived. ? excellent specifcation and high quality - anti-newton ring technology - high reliability materials ? pen/finger, pen only, finger only, light touch types available ? transparency 80% - typical ? rohs compliant input panel panel drive change over switch noise filter mcu control section a/d con - verter interface n part numbers interface controller chips: n 2 n b r e b m u n t r a p e p y t 6 2 0 v - 9 5 5 0 - 0 1 0 3 2 s r , e r i w - 7 7 1 0 0 - 0 2 1 1 4 c s u , e r i w - 7 n part numbers controller boards: n 2 n b r e b m u n t r a p e p y t 0 8 2 b - 8 5 5 0 - b 6 1 3 2 s r , e r i w - 7 0 4 7 b - 8 5 5 0 - b 6 1 s u , e r i w - 7
2 fid-550 series n 1.0 application this specifcation applies to the standard fid-550 series touch panel (pen/finger type). n 2.0 additional applications complete specifcation document is available upon request for customers with whom we have an approved nda in place. n 3.0 discription and block diagram this panel in combination with a control ic chip is used to transfer the co-ordinates of the touched position to the host system (see block diagram above). n 4.0 drawing (please see the diagram above.) defnitions of the major dimensions indicated on this diagram: effective input area (a) area guaranteed to meet all the characteristics detailed in this specifcation view / transparent area (b) the area inside the adhesive zone or electrode pattern. anti-input area (c) an insulating area allowed to protect the touch panel from giving false readings when an enclosure touches the panel. n 5.0 characteristics n 5.1 mechanical operating force 0.05~0.49 n (5 ~ 50gf) measured with a silicon measurement rod r 8 (round type 8mm) silicon rubber hardness 60?c hardness of surface pencil hardness 3h minimum against specifcation jis k-5400 n 5.2 optical transparency 78% min measured in the effective input area to jis k 7105 using a murakami shikisai kenkyusho type iir 100 meter. typically 80%. haze 5% measured in the effective input area using a murakami shikisai kenkyusho type iir 100 meter with an anti glare treated surface. a b c n detailed specification force silicon rubber rod unit: mm (12.50) 93.70 123.75 (23.20) 13.50 (13.50) (12.50) (3.50) 17.20 (13.50) 162.40 215.10 213.10 (input area) 16.00 bottom left to p right (8.00) 22.00 12.50. 5 16.20 180.40 (3.50) 236.80 (24.30) 1 7 (1 1.50) 164.40 (transparent area) (1 1.50) 217.10 (transparent area) 187.40 160.40 (input area) 243.80 46.202.0 3.501.0 15.201.0 24.301.0 48.801.0 3.50 11 .5 0 23.20 47.00 47.0 x 3=141.00 90.51.0 23.201.0 70.201.0 11 8.201.0 164.201.0 n dimension example (10.4 shown)
3 fid-550 series n 5.3 electrical location accuracy: 2.5mm measured over 9 points (see note 1) linearity: 1.5% current consumption: 20ma max at dc 5v when applying 5vdc between pins 3 & 5 switch bounce (chattering): 10ms min when using the silicon rubber measurement rod. insulation resistance: 10m? minimum at 25kv dc applied between pins 3 & 7 or between 5 and 7 dielectric strength: 25kv dc for 1 minute note 1: measurement condition of linearity is corrected within the control ic. in general the location accuracy is specifed as follows: actual co-ordinate point - theoretical co-ordinate point = location accuracy. in general a 9 point co-ordinate calibration system is used to adjust the micro controller accuracy. (20 point can be used in combination with an eeprom design). note 2: pins 3, 5 and 7 are the glass and flm connection points. n 5.4 environmental operating temperature (*): -5?c to 60?c storage temperature: -30?c to 70?c operating humidity: 20% to 90% rh with a maximum wet bulb temperature of 38?c storage humidity: 10% ~ 90% rh with a maximum wet bulb temperature of 38?c chemical resistance: coating with the following chemicals and storing at room temperature for 2 hours gives no problems. 10% nacl-water solution, ethyl-acetate, ethyl- alcohol, toluene, methyl-ethyl-ketone. n 5.5 pen life character writing life: 1,000,000 words minimum touch input life : 10,000,000 times minimum note 1: words are written in the notes area and the size of the word is 7.5mm x 6.75mm. a word is any alphabet / number / mark. the pen is as shown below and applies a force of 250g. a failure is judged to happen when the current consumption or insulation resistance or dielectric strength are not met as shown in 5.3. the location accuracy with 9 point calibration must be 4.4 mm max. 9 mm 10 mm notes effective input area distance co-ordinate point theoretical actual error 3.5 ?6.0 ?2.0 9.0 1.0 11 0.01.0 3.0 1.5 ? 4.6 ?2.0 r 0.8
4 fid-550 series n 5.6 finger life a fnger is simulated by a silicon rubber plunger r8 (round type 8mm size) hardness 60?c at 200g at frequency 5hz. a failure is judged to happen when the current consumption or insulation resistance or dielectric strength are not met as shown in 5.3. the location accuracy with 9 point calibration must be 4.4 mm max. typical operating force is 150g max. n 5.7 information on the panel the panel part number is visible from the flm side the production information is visible from the glass side. production year 99 00 etc. 1 2 3 4 5 6 7 8 9 x y z or 1 2 3 4 5 6 7 8 9 x y z january production 2 3 4 5 6 7 8 9 x y z or 2 3 4 5 6 7 8 9 x y z february production december production n 6 packaging n 6.1 packing specification vibration: 10~55 hz at 1 octave per minute 10g 20 cycles with one side 0.75mm drop test: 60cm drop 1 corner, 3 crease lines and 6 faces. 1 each 1 time after the test no glass: faw or crack is seen, and no dent or scratch on the flm. also glass and flm must not separate. z or 1 2 3 4 5 6 7 8 9 y z n 6.1 packing details each touch panel is placed into a plastic bag and is held in place by a slit cut into the side of the card - board. a second insertion piece is placed into the carton to again add stability. the qty is written on the side of the box. for example the t611 has 26 pieces per box. insert touch panel with bag slit in cardboard
5 fid-550 series n 7.0 reject criteria n o i t p i r c s e d a i r e t i r c t c e j e r t n e d m l i f m m 1 . 0 a e r a 2 m m 5 0 . 0 a e r a 2 m m 1 . 0 < a e r a & 2 m m 5 0 . 0 < a e r a 2 o r e z e b o t : s t n i o p 5 . x a m e b o t : d e i f i c e p s e n o n : n g i e r o f l a i r e t a m n e e w t e b m l i f d n a s s a l g e p y t t o d m m 1 . 0 > a e r a 2 m m 5 0 . 0 a e r a 2 m m 1 . 0 < a e r a & 2 m m 5 0 . 0 < a e r a 2 o r e z e b o t : s t n i o p 5 . x a m e b o t : d e i f i c e p s e n o n : e p y t e n i l m m 1 . 0 a > e r a m m 0 1 < h t g n e l d n a m m 1 . 0 < h t d i w & m m 3 0 . 0 a e r a m m 5 0 . 0 < a e r a o r e z e b o t : t n i o p 1 . x a m e b o t : d e i f i c e p s e n o n : h c t a r c s m m 1 . 0 a e r a m m 0 8 < h t g n e l h t i w m m 1 . 0 < h t d i w & m m 3 0 . 0 a e r a m m 0 3 < h t g n e l h t i w m m 1 . 0 < h t d i w & m m 3 0 . 0 < a e r a o r e z e b o t : t n i o p 1 . x a m e b o t : d e i f i c e p s e n o n : t a o c d r a h r o r u l b t o d g n i s s i m m m 5 . 0 a e r a 2 m m 3 0 . 0 a e r a 2 m m 5 . 0 < a e r a & 2 m m 5 0 . 0 < a e r a 2 o r e z e b o t : s t n i o p 5 . x a m e b o t : d e i f i c e p s e n o n : g n i r n o t w e n 3 ( p m a l t n e c s e r o u l f a r e d n u e d i s m l i f l e n a p m o r f n e e s e b t o n t s u m e s e h t . e d i s s s a l g m r o f d e i f i r e v e b o t t o n . ) p m a l e p y t h t g n e l e v a w w a l f s s a l g e h t . m a r g a i d g n i w o l l o f e h t n i n w o h s t a h t n a h t r e g g i b s i h c i h w w a l f o n e b o t . d e i f i c e p s t o n s i s w a l f f o r e b m u n n 8.0 general points of caution touch panels are made of glass, so care must be taken in handling them. do not stress, pile, bend, lift by the cable or put any stress on the flm, for example moving by flm face vacuum. in order to clean wring dry a cloth which has been emersed in a natural detergent. do not use any organic solvent, acid or alkali solu - tion. watch the edge of the panel when cleaning, again for safety reasons. 2m m 2m m 5m m 3m m
6 fid-550 series n 9.0 connection and mounting the details below indicate the recommended mounting structure for panel and enclosure. the enclosure sup - port to fx the touch panel must be over 1.0mm i width and must be outside the view (t ransparent area). also ensure that the enclosure does not cause miss input by touching the view area. the following diagram shows that the enclosure edge must be between the view area and the guaranteed ac - tive area. ensure space is allocated for the diodes, and we recommend that the material to fx the panel and enclosure is elastic. special design would be required to stop water ingress. the corners of the touch panel are conductive so do not touch any metal parts after mounting. location detect 1. right/ upper glass 2. right/ upper glass 3. each side glass 4. left/ lower glass 5. each side glass 6. left/ lower glass 7. all film bottom view (drawing, with conductive side up) (mating connector type fci or equivalent sfw15r-1stae1-lf: for fpc) 0.8 mm min. connector lcd 1.0 to 3.0 m m circuit board tr ansparent area anti-input area shock absorber to protect the panel (eg rubber) upper case input area shock absorber for protection vi ew area input panel wiring area cut-out / avoidance of 550 surface mount diodes conductive face fpc-type cable contact section v iew laminate film stif fener board 0.30.05 2.0 1.1 1.2 0.7 3.35 2.0 top view (picture, with conductive side down)
7 fid-550 series n 10.0 panel thickness 2. 6 ma x 1. 4 thickness of glass 1.1mm stif fener boar d conductive face japan fujitsu component limited gotanda-chuo building 3-5, higashigotanda 2-chome, shinagawa-ku tokyo 141 8630, japan tel: (81-3) 5449-7010 fax: (81-3) 5449-2626 email: promothq@fcl.fujitsu.com web: www.fcl.fujitsu.com north and south america fujitsu components america, inc. 250 e. caribbean drive sunnyvale, ca 94089 u.s.a. tel: (1-408) 745-4900 fax: (1-408) 745-4970 email: components@us.fujitsu.com web: http://us.fujitsu.com/components/ europe fujitsu components europe b.v. diamantlaan 25 2132 wv hoofddorp netherlands tel: (31-23) 5560910 fax: (31-23) 5560950 email: info@fceu.fujitsu.com web: emea.fujitsu.com/components/ asia pacifc fujitsu components asia ltd. 102e pasir panjang road #01-01 citilink warehouse complex singapore 118529 tel: (65) 6375-8560 fax: (65) 6273-3021 email: fcal@fcal.fujitsu.com web: http://www.fujitsu.com/sg/services/micro/components/ fujitsu components international headquarter offces ?2007 fujitsu components america, inc. all rights reserved. all trademarks or registered trademarks are the property of their respective owners. fujitsu components america or its affliates do not warrant that the content of datasheet is error free. in a continuing effort to improve our products fujitsu components america, inc. or its affliates reserve the right to change specifcations/datasheets without prior notice. rev. may 30, 2007.
|
